Wall Mount for Garden Hose: A Step-by-Step Guide to Tidy Storage

By Caleb Morgan

Updated November 2026

A wall mount for garden hose gives you a fixed, off-the-ground place to store your hose, which keeps it from kinking, cracking in the sun and tripping people on the walkway. In this guide you will learn how to pick the right type of wall mount, decide where to put it, install it securely into wall studs or masonry, and set up the hose so it coils and retracts without a fight. The steps below work for most homes, whether you are mounting a simple hook bracket or a full wall-mounted reel.

Why a Wall Mount Beats Leaving the Hose on the Ground

A hose left coiled in a puddle or dragged across the lawn takes a lot of abuse. Sunlight breaks down the rubber and vinyl, grit wears the inner lining, and repeated kinking weakens the walls at the bends. A wall mount lifts the hose clear of the ground, lets it drain and dry, and keeps it in one predictable spot. Owners often report that a mounted hose lasts noticeably longer than one stored loose, mainly because it is not being stepped on, run over or left in the heat all afternoon.

Shopping for one? See our guide: 6 Best Garden Hose Reel Wall Mount Options of 2026.

Choose the Right Type of Wall Mount

Not every wall mount works the same way. Before you buy anything, decide how you plan to store the hose and how much hose you have.

Simple Hook or Bracket Mounts

These are the most basic option: a metal or plastic hook, sometimes with a curved arm, that holds a loosely looped hose. They are inexpensive, quick to install and fine for a short hose of 50 feet or less. The drawback is that you coil the hose by hand each time, and a long hose can sag or slip off the hook.

Hose Reel Wall Mounts

A wall-mounted reel holds the hose on a drum that you rewind with a crank or a spring-assisted handle. These suit longer hoses, usually 75 feet and up, and they keep the coil neat. Some models are designed to hold hose only, while others include a built-in hose guide that spreads the coil evenly across the drum. A heavy-duty reel with a sturdy steel or reinforced polymer frame is a better choice if you have a long hose or use a lot of water.

Multi-Hose or Combination Mounts

If you have two hoses, or a hose plus an extension, a combination bracket with multiple arms can keep everything in one place. Check that the arms are spaced far enough apart that the coils do not press against each other.

Check Your Wall and Gather Tools

The biggest reason wall mounts fail is poor attachment to the wall, not the mount itself. A reel or heavy bracket pulls on the wall every time you wind or unwind a long hose, so the anchor points matter.

Identify What Your Wall Is Made Of

• Wood-framed walls (siding over studs): Use a stud finder to locate the vertical studs, usually spaced 16 inches apart on center. Drive lag screws into the studs.
• Brick or concrete block: Drill into the mortar joint or solid block with a masonry bit, then insert masonry anchors or sleeve anchors rated for the load.
• Vinyl or fiber-cement siding over sheathing: Locate the studs behind the siding, and fasten through the siding into the stud, not just into the siding itself.

Tools and Supplies You Will Need

1. Stud finder
2. Pencil and level (a 24-inch level works well)
3. Drill with the correct bit for your fasteners
4. Masonry bit if you are mounting into brick or block
5. Lag screws, anchors or wall plugs sized for the mount
6. Socket or wrench for lag screws
7. Tape measure
8. Exterior-rated silicone or sealant, if you drill through siding

Pick the Best Location and Height

Location affects how easy the hose is to use and how long it lasts. Aim for a spot near your main outdoor faucet so the hose connects with minimal dragging. Avoid placing the mount where the hose will be pinched by a door, gate or swinging shutter.

Step-by-Step Installation

1. Mark the location. Hold the mount against the wall at your chosen height and check it with a level. Mark the screw holes with a pencil.
2. Find and mark the studs. Confirm each mounting hole lines up with a stud, or plan for masonry anchors if the wall is brick or block.
3. Drill pilot holes. Drill slightly smaller than the diameter of your lag screws in wood, or the correct size for your masonry anchors. Drill straight and to the depth specified by the anchor or screw.
4. Seal the holes if drilling through siding. Apply a bead of exterior silicone or sealant in each hole before inserting the fastener. This helps prevent water from wicking into the wall.
5. Attach the mount. Drive the lag screws or insert the anchors and tighten until the mount is firm. Do not overtighten, which can crack siding or strip the anchor.
6. Test the load. Hang a coiled hose and give the mount a firm tug. Wind and unwind a reel a few times to check for movement or flex.
7. Store the hose. Drain water out of the hose first, then coil it loosely in the same direction each time to reduce twisting.

Coiling the Hose Correctly

For a hook mount, make large loops of 2 to 3 feet, laying each loop flat rather than stacking it. For a reel, start the winding at the reel end and let the guide spread the hose evenly. Coiling in the same direction helps prevent kinks and keeps the hose from developing a permanent spiral.

Tips for a Lasting Installation

• Use stainless steel or galvanized fasteners in exterior locations to reduce rust streaks.
• Recheck the lag screws once or twice a year, especially after heavy use or freeze-thaw cycles.
• Keep the mount free of spider webs and debris so the hose slides on and off smoothly.
• If the hose is kinked at the mount, add a small offset spacer behind the bracket so the hose bends gently.
• Store nozzles and fittings separately so they do not bang against the wall or damage the hose ends.

Common Mistakes

• Relying on siding alone. Vinyl and thin fiber-cement siding cannot hold a loaded reel by itself. Always fasten into studs or solid masonry.
• Mounting too high. A hook above shoulder height makes lifting and coiling awkward, and people often stop using it.
• Trapping water. Storing a wet hose tightly coiled encourages mildew and internal degradation. Drain it first.
• Using the wrong anchors. Drywall anchors or light plastic plugs fail under the pull of a long hose.
• Ignoring the hose length. A short hook on a 100-foot hose will sag, slip or tangle. Match the mount to the hose.

Recommended gear

A solid installation depends mostly on good fasteners and accurate marking. The following items help with the most common mounting situations.

• Stud finder: Locating studs accurately is the single most important step for a secure reel or heavy bracket, and a quality electronic finder makes it quicker. View on Amazon
• Masonry drill bit set: Needed if you are mounting into brick or concrete block, where a standard wood bit will not cut cleanly. View on Amazon
• Stainless steel lag screws: Resist rust and streaking better than plain steel, which matters for an outdoor mount. View on Amazon
• Exterior silicone sealant: Seals drilled holes through siding so water does not seep behind the mount. View on Amazon

FAQ

Can I mount a garden hose reel on siding without hitting a stud?

Not safely for a loaded reel. Siding is not designed to carry that pull, so fasten through the siding into a stud or into solid masonry instead. For a light hook holding a short hose, a properly rated anchor may be enough, but checking for a stud is still the safer choice.

How high should a wall mount for garden hose be?

Most people find a height of roughly 30 to 48 inches comfortable. This keeps the hose off the ground and makes it easy to reach the coil without bending far or lifting heavily.

Should I drain the hose before storing it on a wall mount?

Yes. Drain the water from the hose before coiling it, and try to store it somewhere it will not freeze. Water left inside can freeze and crack the hose, and a wet hose stored tightly coiled can develop mildew.

What is the difference between a hose hook and a hose reel?

A hook holds a loosely coiled hose and is best for shorter lengths. A reel stores the hose on a drum that you wind up, which keeps longer hoses neater and easier to deploy.

Can I mount a hose on brick or concrete?

Yes. Use a masonry bit to drill into the mortar joint or solid block, then insert masonry anchors or sleeve anchors rated for the weight of the mount plus the hose. Avoid drilling into hollow block without checking the anchor manufacturer’s guidance.

How do I stop my hose from kinking at the wall mount?

Leave a bit of slack so the hose does not bend sharply where it meets the bracket. A small spacer or offset arm can push the hose away from the wall, giving it a gentler curve.

How often should I check the mounting hardware?

Check the screws or anchors at least once or twice a year and after any period of heavy use. Freeze-thaw cycles and the weight of a wet hose can loosen fasteners over time.

Conclusion

A wall mount for garden hose is one of the simplest upgrades you can make to your outdoor setup. Choose a mount type that matches your hose length, locate solid anchor points in the studs or masonry, and mount it at a comfortable height near your faucet. With the hose drained and coiled neatly after each use, it will stay tidier and last longer. For guidance on related setup tasks, see Garden Hose to Faucet: Step-by-Step Connection Guide (5 Steps) and Garden Tool Storage Guide: Racks, Sheds and Walls.

Related reading

• Wall Mounted Garden Hose Reels: A Step-by-Step Installation and Buying Guide
• Zero-G Ultra Flexible Durable Garden Hose: 7 Best Picks Compared (2026)
• Zero G Garden Hose: Pros, Cons and How to Use One Well

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our garden hand tools & equipment guides, checking product details against manufacturer specifications and owner feedback.