Updated November 2026

Garden hose size thread refers to the standard threaded connection that joins your hose to spigots, nozzles, sprayers and adapters. In North America, nearly every residential hose uses the same design, known as garden hose thread (GHT), so most fittings will fit together without trouble. This guide shows you how to confirm your thread size, measure it accurately, and pick the right replacement or adapter the first time.

Understand the Standard Garden Hose Thread Size

The thread size for garden hose connections in the United States is 3/4 inch, measured as the outside diameter of the male threads. The pitch is 11.5 threads per inch, and the threads are straight rather than tapered, so they seal with a rubber washer rather than thread tape. Manufacturers typically label these fittings as GHT or “hose thread,” and many brand-name spigots and nozzles follow this standard. Keep in mind that the 3/4-inch figure describes the thread, not the hose’s inside diameter, which is a separate measurement.

Shopping for one? See our guide: Zero-G Ultra Flexible Durable Garden Hose: 7 Best Picks Compared (2026).

How to Measure and Identify Your Thread

You can confirm the thread size of a garden hose connection with a few basic tools. Start by checking the packaging or any stamped markings on the fitting, since many parts list “3/4 GHT” directly. If nothing is printed, use the steps below.

  1. Unscrew the fitting and inspect the threads. Straight, rounded threads with a rubber washer seat are GHT.
  2. Measure the outside diameter of the male threads with a caliper or ruler. A reading close to 0.75 inch (3/4 inch) confirms standard GHT.
  3. Count the threads over one inch using a thread gauge or the edge of a ruler. Eleven to twelve threads per inch matches GHT.
  4. Check for a washer seat. A flat, recessed face at the end of the fitting is standard on hose ends.
  5. If the threads are tapered like pipe, you have National Pipe Thread (NPT) fittings, which will not seal properly with a hose.

Match Fittings and Avoid Common Compatibility Problems

Once you know your garden hose thread sizes, matching parts becomes straightforward. The table below covers the most common connections you are likely to encounter.

Connection type Typical thread Works with standard hose?
Outdoor spigot 3/4 GHT Yes
Hose nozzle or sprayer 3/4 GHT Yes
Hose-to-hose connector 3/4 GHT both ends Yes
Indoor faucet aerator Pipe thread (NPT) No, needs an adapter
Pressure washer outlet Varies by model Check the manual

When a fitting does not seat, the cause is usually a mismatch between GHT and pipe thread, or a damaged washer. Replacing a worn washer solves most leaks, and a GHT-to-NPT adapter bridges the gap when you need to connect a pipe-threaded fixture. For a deeper look at sealing options, see Teflon Tape Garden Hose: How to Seal Threads Without Leaks, which explains when tape helps and when it does more harm than good.

Choose Replacement Ends and Adapters Wisely

If your hose end is cracked or crushed, you can replace it instead of buying a new hose. Measure the thread first, then choose a repair end that matches the hose’s inside diameter, since a fitting that is too large or too small will leak or pull loose under pressure. Crimp-on and clamp-on styles both work, though clamp-on types are easier to install at home. For a comparison of repair options, see Replace End of Garden Hose: 6 Best Repair Fittings Compared (2026).

Adapters can also bring a hose to a different outlet. A quick-connect system uses the same 3/4 GHT base, so you can add it without changing your spigot. Guidance on that setup is in Quick Connect for Garden Hose: How to Choose and Install One (Step-by-Step).

Common Mistakes

  • Assuming all hose fittings are the same. Indoor faucets and some pressure washers use different threads.
  • Using thread tape on GHT fittings. The washer seals the joint, and tape can cause leaks or make threads hard to separate.
  • Overtightening plastic fittings, which can crack the threads.
  • Ignoring a worn or flattened rubber washer. Replace it whenever you see cracks or flat spots.
  • Measuring the hose’s inside diameter and calling it the thread size. The two are different measurements.

A digital or dial caliper makes it easy to measure the outside diameter of threads accurately. View on Amazon

A thread pitch gauge lets you count threads per inch and confirm GHT versus pipe thread in seconds. View on Amazon

Replacement rubber hose washers keep connections sealed and are inexpensive to keep on hand. View on Amazon

FAQ

What is the standard thread size for a garden hose?

The standard is 3/4 inch garden hose thread (GHT), with 11.5 threads per inch. Most spigots, nozzles and hose connectors in North America use this size.

Can I use a pipe-thread fitting on a garden hose?

Not directly. Pipe threads are tapered and will not seal with a washer, so you need a GHT-to-NPT adapter to connect them.

How do I know if my hose end is damaged?

Look for cracks, flattened threads, or a washer that no longer sits flush. Any of these signs means the fitting or washer should be replaced.

Conclusion

Garden hose size thread is almost always 3/4 inch GHT, and checking the threads with a caliper and a pitch gauge takes only a few minutes. Once you confirm the size, matching nozzles, adapters and repair ends is simple. Keep spare washers on hand, and you can avoid most leaks before they start.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our garden hand tools & equipment guides, checking product details against manufacturer specifications and owner feedback.