Updated November 2026
Fiskars pruning shears replacement parts are easy to find once you know what your pair is called and which component has worn out. Most of the time, the blade, the spring, or the pivot bolt is the piece that needs replacing, and a few tools and a careful eye are enough to swap it. This guide shows you how to identify your model, check what can be replaced, and rebuild the shears without buying a new pair.
Identify Your Model Before You Order Anything
Replacement parts are model-specific, so start by finding the exact model number. Look for it stamped on the handle, the blade base or the packaging. Fiskars uses different blade shapes, spring designs and bolt sizes across its bypass and anvil lines, and a blade that fits one model may not fit another. If you can’t read the number, measure the blade length and note whether the shears cut with a curved blade sliding past a straight one (bypass) or a blade pressing onto a flat surface (anvil).
Shopping for one? See our guide: 3 Best Milwaukee M18 Brushless Telescoping Pole Pruning Shears (2026).
Check Which Parts Are Replaceable
Not every component is sold separately, but the parts that wear most often usually are. In general, you can expect the following:
- Blades: the cutting edge dulls over time, and a replacement blade is often the most useful part to buy.
- Springs: a weak or broken spring makes the handles snap open slowly or not at all.
- Pivot bolt and nut: a loose bolt causes wobble and uneven cutting, and it is cheap to replace.
- Bumpers and grips: rubber bumpers and soft grips can often be ordered separately.
Check the official Fiskars website or an authorized parts seller for current availability, since listings change. Shears that are very old or heavily damaged may be better replaced outright.
How to Replace a Blade or Spring Step by Step
Work on a clean, flat surface with good light. Keep the shears closed and wear gloves, because blades are sharp even when dull.
- Remove the pivot bolt with a screwdriver or hex key that fits snugly. A loose fit can strip the head.
- Separate the two halves carefully. Note how the spring, washers and bushings sit before you lift them out.
- Fit the new blade or spring in the same orientation as the old one. Blades usually sit on the side with the cutting edge facing the correct direction, so compare them side by side.
- Reassemble with the bolt, tightening until the blades meet with light resistance and still pivot smoothly. Back off slightly if the handles feel stiff.
- Test with a few cuts on a stem you don’t mind losing, then adjust the bolt if the cut tears instead of slicing.
Common Mistakes to Avoid
- Ordering a part without confirming the model number first, which leads to returns.
- Overtightening the pivot bolt, which pinches the blades and makes them hard to open.
- Reassembling washers or bushings in the wrong order, causing uneven blade contact.
- Skipping a sharpening pass after installing a new blade, which can leave the edge slightly rough at first.
- Forcing a stripped bolt head instead of replacing the bolt.
Recommended gear
A few basics make the repair faster and safer. A small set of hex keys or screwdrivers that match the bolt head prevents stripping. Cut-resistant gloves protect your hands while you handle exposed blades. A fine sharpening stone or file keeps a freshly installed blade working cleanly.
- Hex key set for pruning shears – matches the common bolt sizes so you don’t strip the head. View on Amazon
- Cut-resistant work gloves – protect your hands while you handle blades during reassembly. View on Amazon
- Fine diamond sharpening file – restores the edge on a new or lightly dulled blade. View on Amazon
FAQ
Can I replace just the blade without buying a whole new pair?
In most cases yes, provided the blade is sold for your specific model. Confirm the model number first, since blade shapes differ between lines.
How do I know if my spring needs replacing?
If the handles open slowly, stay closed or don’t return fully after each cut, the spring is likely weak or broken. Replacing it usually restores the snap.
Is it worth repairing old Fiskars shears?
If the frame is intact and the blades can still be sharpened or replaced, repair is usually sensible. If the frame is cracked or bent, replacing the whole tool is safer.
Conclusion
Finding the right fiskars pruning shears replacement parts starts with the model number and a clear idea of which part has failed. Blades, springs and pivot bolts are the most common repairs, and most can be swapped with basic tools. Work carefully, test your cuts, and you can extend the life of your shears considerably.
