Updated November 2026
Garden hose thread dimensions follow a single North American standard, so most fittings will mate if you know what to measure. This guide explains the standard size, shows you how to measure an existing hose end or spigot, and helps you avoid the leaks that come from mismatched threads.
Understand the Standard Garden Hose Thread
In the United States and Canada, the standard is called GHT, short for garden hose thread. It uses a 3/4-inch nominal diameter with 11.5 threads per inch. The thread is straight rather than tapered, which means the seal comes from a rubber washer inside the fitting, not from the threads themselves. Manufacturers specify this size for hose ends, spigots, sprinklers, nozzles and most hose reels.
Shopping for one? See our guide: Zero-G Ultra Flexible Durable Garden Hose: 7 Best Picks Compared (2026).
How to Measure an Existing Thread
Measuring takes about five minutes and needs only basic tools. Work through these steps:
- Unscrew the fitting and check for a rubber washer. Note whether it is seated in the female end.
- Measure the outside diameter of the male threads with a caliper. A standard GHT male thread measures close to 1 inch across the crests.
- Count the threads over one inch. Standard GHT shows 11 to 12 threads per inch.
- Confirm the thread profile. GHT threads are straight and rounded, while pipe threads (NPT) are tapered.
Compare Common Thread Types
Several thread types look similar, and mixing them is the most common cause of a cross-threaded fitting. The table below summarizes the main ones.
| Thread type | Thread form | Typical use |
|---|---|---|
| GHT (garden hose) | Straight, 11.5 TPI | Hoses, spigots, nozzles |
| NPT (pipe) | Tapered | Plumbing, some irrigation parts |
| BSP (British pipe) | Straight or tapered, 14 TPI at 3/4 inch | Imported equipment |
If a fitting feels tight but will not seat fully, check whether it is a tapered pipe thread. Forcing a tapered thread onto a GHT fitting can damage both parts. A broader overview of mating parts is available in Quick Connect for Garden Hose: How to Choose and Install One (Step-by-Step).
Match Threads and Seal Connections
Once you know the thread is GHT, match the male and female ends and check the washer. A worn or missing washer causes more drips than thread size does. Replace it with a new rubber washer of the same diameter. For fittings that need extra sealing, thread tape can help, but it should go on the male pipe threads only, never on a GHT hose connection, since the washer does the sealing. For guidance on tape, see Teflon Tape Garden Hose: How to Seal Threads Without Leaks.
When buying a replacement end, confirm the fitting size against the hose diameter as well. A 5/8-inch hose needs a barb or crimp that matches that bore, even if the thread is standard. For options, see Replacement Garden Hose Ends: 7 Best Repair Fittings Compared (2026).
Recommended gear
A digital caliper makes it simple to measure outside diameter and confirm a thread isn’t tapered: View on Amazon.
Replacement rubber washers are inexpensive and are the part most likely to fix a leak: View on Amazon.
Common Mistakes
- Assuming all threads with a 3/4-inch label are GHT. Pipe threads often share the same nominal size.
- Putting thread tape on a GHT connection, which can prevent the washer from seating.
- Forcing a fitting that does not start by hand. Stop and check the profile.
- Replacing the hose end but ignoring the hose bore, leading to a loose clamp.
- Overtightening plastic fittings, which can crack the threads.
FAQ
What is the standard garden hose thread size?
The standard is GHT, with a 3/4-inch nominal diameter and 11.5 threads per inch. It is used for most hoses, spigots and nozzles in North America.
Can I use a pipe thread fitting on a garden hose?
Usually not. Pipe threads are tapered and will not seal against the rubber washer properly, and they can cross-thread a GHT connection.
Do I need thread tape on hose connections?
No. The rubber washer creates the seal on GHT fittings. Thread tape belongs on tapered pipe threads, not on standard garden hose connections.
Conclusion
Most garden hose fittings in North America use the standard GHT thread, so measuring the diameter and thread count will usually settle compatibility. Check the washer, avoid tape on hose connections and confirm the hose bore before buying. Following these steps should prevent most leaks and damaged threads.

Write Your Review
No reviews yet. Be the first to share your experience!